Feed Program

FloraPro® Powder High EC Stock Solution Feed Program

Use the FloraPro Powder High EC feed chart for higher-EC production in coco or rockwool. Find weekly stock-solution doses and EC, pH, and nitrogen targets from propagation through finish.
Hydroponics Coco Coir Rockwool High EC 1.0lb/gal
Delivery Stock Solution Injection
EC High EC
Schedules 1

Dosage calculator

Calculate your reservoir mix

Choose a week and enter your reservoir size to calculate total nutrients for one mix.

Choose a schedule and week to calculate dosage.

Always add nutrients one at a time, mix thoroughly between products, and check pH/EC after mixing.

Commercial Powder Feed Program
Notes

The online calculator uses the base recipe. The chart’s nutrient-solution pH targets are for coco and rockwool. For peat-based media, target pH 6.0–6.4 from propagation through finish. 

If substrate EC is rising, review the growing environment and runoff before changing the recipe. If an adjustment is still needed, lower each FloraPro powder dose proportionally by 10–15%. To raise feed strength in veg, increase each FloraPro powder dose proportionally by 10–15%. To raise feed strength in flower, increase Late Bloom alone by 10–15% to limit added nitrogen. Monitor crop response before adjusting again. Follow the chart’s separate TrueFlo instructions. Contact General Hydroponics Technical Services for significant or site-specific changes. 

For an eight-week flowering schedule, skip Early Flower week 3. After Early Flower week 2, move to the Mid Flower recipe and continue the remaining recipes in order at their listed rates.

Overview

Phases

Vegetative

3 wk
Details

Vegetative growth stage targets.

Use High EC where the crop and growing environment can support the higher feed strength. For extended veg, begin with the Standard Vegetative recipe and step up to High EC later in veg as conditions and crop response warrant. Record root-zone EC and pH early so you can track the effect of the transition. Increase irrigation as roots expand while allowing enough dry-back for root-zone oxygen. If stems soften or spacing between nodes increases excessively, review nitrogen and irrigation together.

Early Flower

3 wk
Details

Transition/early flowering targets.

Start Bloom and Late Bloom together with Calcium + Micros. During weeks 2 and 3, track stretch, stem firmness, root-zone EC and pH, and substrate moisture. Use those readings to check for salt buildup or excessive irrigation as the crop transitions. If excessive nitrogen or irrigation is contributing to stretch, review irrigation and consider moving to the lower-nitrogen Mid Flower recipe one week earlier. For an eight-week flowering schedule, skip Early Flower week 3 and move directly from week 2 to the Mid Flower recipe.

Mid Flower

3 wk
Details

Peak flower development targets.

Watch root-zone EC, pH, and irrigation closely as flower development drives peak nutrient demand. Check root-zone readings before changing the recipe in response to visual symptoms. If leaf margins begin to burn, check for salt buildup and review irrigation before increasing feed strength. Maintain airflow and humidity that support transpiration and nutrient transport.

Late Flower

2 wk
Details

Late flower bulking targets.

Continue both Bloom and Late Bloom at the listed rates while the chart reduces nitrogen. Watch for gradual, even fade and check root-zone EC as the recipe tapers. If fade is patchy, investigate possible imbalances before making another feed cut. Continued Nitrogen reduction is critical during the final stages of flower development. Feed 10–14 days on the Late Flower recipe before moving to Finish or plain water flush prior to harvest.

Finish

1 wk
Details

Finish / pre-harvest targets.

Use Late Bloom and Calcium + Micros at the listed Finish rates. Late Bloom itself contains no nitrogen, and Calcium + Micros continues to supply nitrogen in the Finish recipe. The guide presents this recipe as an option for shortening or replacing a plain-water flush. Monitor how quickly fan leaves fade and whether they remain functional as flowers mature. Use trichome maturity to confirm harvest timing.

Weekly reference View week-by-week feed program Expand for weekly dosages, EC/PPM targets, growth stages, and product-by-product feeding details.
Week N Targets Feed
Propagation
Details

Stock-solution targets for propagation

Soak clone plugs in the prepared propagation feed before inserting cuttings. Keep the substrate evenly moist and avoid aggressive dry-backs while roots establish. As roots emerge, rapidly scale nutrient concentration towards vegetative strength to maximize early biomass development.

Propagation — Wk 1
W1 P1 Propagation
60
EC0.6 - 0.8 pH5.5 - 5.8
Vegetative
Details

Vegetative growth stage targets.

Use High EC where the crop and growing environment can support the higher feed strength. For extended veg, begin with the Standard Vegetative recipe and step up to High EC later in veg as conditions and crop response warrant. Record root-zone EC and pH early so you can track the effect of the transition. Increase irrigation as roots expand while allowing enough dry-back for root-zone oxygen. If stems soften or spacing between nodes increases excessively, review nitrogen and irrigation together.

Vegetative — Wk 1
W2 P1 Vegetative
250
EC2.5 - 2.7 pH5.6 - 6.1
Vegetative — Wk 2
W3 P2 Vegetative
250
EC2.5-2.7 pH5.6 - 6.1
Vegetative — Wk 3
W4 P3 Vegetative
250
EC2.5-2.7 pH5.6 - 6.1
Early Flower
Details

Transition/early flowering targets.

Start Bloom and Late Bloom together with Calcium + Micros. During weeks 2 and 3, track stretch, stem firmness, root-zone EC and pH, and substrate moisture. Use those readings to check for salt buildup or excessive irrigation as the crop transitions. If excessive nitrogen or irrigation is contributing to stretch, review irrigation and consider moving to the lower-nitrogen Mid Flower recipe one week earlier. For an eight-week flowering schedule, skip Early Flower week 3 and move directly from week 2 to the Mid Flower recipe.

Early Flower — Wk 1
W5 P1 Early Flower
210
EC2.6 - 2.8 pH5.7 - 6.2
Early Flower — Wk 2
W6 P2 Early Flower
210
EC2.6 - 2.8 pH5.7 - 6.2
Early Flower — Wk 3
W7 P3 Early Flower
210
EC2.6 - 2.8 pH5.7 - 6.2
Mid Flower
Details

Peak flower development targets.

Watch root-zone EC, pH, and irrigation closely as flower development drives peak nutrient demand. Check root-zone readings before changing the recipe in response to visual symptoms. If leaf margins begin to burn, check for salt buildup and review irrigation before increasing feed strength. Maintain airflow and humidity that support transpiration and nutrient transport.

Mid Flower — Wk 4
W8 P4 Mid Flower
185
EC2.4 - 2.6 pH5.7 - 6.2
Mid Flower — Wk 5
W9 P5 Mid Flower
185
EC2.4 - 2.6 pH5.7 - 6.2
Mid Flower — Wk 6
W10 P6 Mid Flower
185
EC2.4 - 2.6 pH5.7 - 6.2
Late Flower
Details

Late flower bulking targets.

Continue both Bloom and Late Bloom at the listed rates while the chart reduces nitrogen. Watch for gradual, even fade and check root-zone EC as the recipe tapers. If fade is patchy, investigate possible imbalances before making another feed cut. Continued Nitrogen reduction is critical during the final stages of flower development. Feed 10–14 days on the Late Flower recipe before moving to Finish or plain water flush prior to harvest.

Late Flower — Wk 7
W11 P7 Late Flower
115
EC1.9 - 2.1 pH5.7 - 6.2
Late Flower — Wk 8
W12 P8 Late Flower
115
EC1.9 - 2.1 pH5.7 - 6.2
Finish
Details

Finish / pre-harvest targets.

Use Late Bloom and Calcium + Micros at the listed Finish rates. Late Bloom itself contains no nitrogen, and Calcium + Micros continues to supply nitrogen in the Finish recipe. The guide presents this recipe as an option for shortening or replacing a plain-water flush. Monitor how quickly fan leaves fade and whether they remain functional as flowers mature. Use trichome maturity to confirm harvest timing.

Finish — Wk 9
W13 P9 Finish
50
EC1.5 - 1.7 pH5.7 - 6.2
Propagation
Details

Stock-solution targets for propagation

Soak clone plugs in the prepared propagation feed before inserting cuttings. Keep the substrate evenly moist and avoid aggressive dry-backs while roots establish. As roots emerge, rapidly scale nutrient concentration towards vegetative strength to maximize early biomass development.

Vegetative
Details

Vegetative growth stage targets.

Use High EC where the crop and growing environment can support the higher feed strength. For extended veg, begin with the Standard Vegetative recipe and step up to High EC later in veg as conditions and crop response warrant. Record root-zone EC and pH early so you can track the effect of the transition. Increase irrigation as roots expand while allowing enough dry-back for root-zone oxygen. If stems soften or spacing between nodes increases excessively, review nitrogen and irrigation together.

Early Flower
Details

Transition/early flowering targets.

Start Bloom and Late Bloom together with Calcium + Micros. During weeks 2 and 3, track stretch, stem firmness, root-zone EC and pH, and substrate moisture. Use those readings to check for salt buildup or excessive irrigation as the crop transitions. If excessive nitrogen or irrigation is contributing to stretch, review irrigation and consider moving to the lower-nitrogen Mid Flower recipe one week earlier. For an eight-week flowering schedule, skip Early Flower week 3 and move directly from week 2 to the Mid Flower recipe.

Mid Flower
Details

Peak flower development targets.

Watch root-zone EC, pH, and irrigation closely as flower development drives peak nutrient demand. Check root-zone readings before changing the recipe in response to visual symptoms. If leaf margins begin to burn, check for salt buildup and review irrigation before increasing feed strength. Maintain airflow and humidity that support transpiration and nutrient transport.

Late Flower
Details

Late flower bulking targets.

Continue both Bloom and Late Bloom at the listed rates while the chart reduces nitrogen. Watch for gradual, even fade and check root-zone EC as the recipe tapers. If fade is patchy, investigate possible imbalances before making another feed cut. Continued Nitrogen reduction is critical during the final stages of flower development. Feed 10–14 days on the Late Flower recipe before moving to Finish or plain water flush prior to harvest.

Finish
Details

Finish / pre-harvest targets.

Use Late Bloom and Calcium + Micros at the listed Finish rates. Late Bloom itself contains no nitrogen, and Calcium + Micros continues to supply nitrogen in the Finish recipe. The guide presents this recipe as an option for shortening or replacing a plain-water flush. Monitor how quickly fan leaves fade and whether they remain functional as flowers mature. Use trichome maturity to confirm harvest timing.

Included

Products

Guidance Mixing Notes

Prepare and verify stock
Prepare each FloraPro powder as a separate stock solution. Keep Calcium + Micros separate from Grow, Bloom, and Late Bloom at stock strength. Fill a clean tank with RO water to about 70% of the planned final volume. Slowly add the full bag while agitating. Mix for 15–30 minutes or until fully dissolved. Top up with RO water to 1 lb of powder per gallon of finished concentrate. Mix for another 15–30 minutes until clear and uniform. 

To verify a batch, mix 10 mL of one stock with 1,990 mL of RO water. Measure with a calibrated EC meter and compare the reading with your facility’s benchmark for that component. This 1:200 dilution is a stock quality check. 

Deliver the finished feed
Measure each stock separately. When dosing manually, add one input at a time to the feed water, mix thoroughly between additions, and check EC and pH. For batch-tank or direct-to-crop injection, follow the chart’s mixing order. A mixing chamber is strongly recommended between the Calcium + Micros injection point and the other base inputs. 

Use the TrueFlo rate for your recipe and growth stage. These charts specify TrueFlo at 0.028% HOCl. Add it after the nutrient solution pH has been lowered. For best results, apply TrueFlo at pH 4.0–6.5.

Feed Program Resources

Search