Diamond Nectar®

Premium Grade Humic Acids General Hydroponics View available resources

Diamond Nectar® accelerates nutrient absorption where mineral foods enter the plant. Diamond Nectar® applies the chelating action of humic acids to nutrient rich hydroponic environments by grabbing immobile and molecularly heavy compounds. They are transported through and into plant tissues for faster growth and greater yields. Diamond Nectar® supercharges your nutrients in order to optimize the health of your plants and the quality of your crops.

Available sizes

Diamond Nectar accelerates nutrient absorption where mineral foods enter the plant

Diamond Nectar applies the chelating action of humic acids to nutrient rich hydroponic environments by grabbing immobile and molecularly heavy compounds

They are transported through and into plant tissues for faster growth and greater yields

For use with

Plants

  • Hemp
  • Vegetables
  • Herbs
  • Fruits
  • Flowers
  • Other high value crops

Media

  • Rockwool
  • Potting mix
  • Coco
  • Peat lite mix
  • In-ground soil
  • Water culture

Guaranteed analysis

  • n0
  • p1
  • k1

Derived from: Phosphoric Acid and Potassium Hydroxide

  • Available Phosphate (P2O5) 1.0%
  • Soluble Potash (K2O) 1.0%

Find your feedchart

Ready to get the most out of your grow? View and download grower-tested feed charts for all GH nutrients and supplements and succeed at every phase of the growing cycle.

Commercial Growers

Donec et purus at dolor pellentesque laoreet. Pellentesque tempus justo non nisl pretium, a mattis nibh vestibulum. Praesent ex justo, cursus a ligula tempus, suscipit blandit nisi.

Getting started

Learn from the best

FAQs

View all FAQs
  • Our Pro Feedchart Usage Guide explains how to interpret and use General Hydroponics Pro Feedcharts. It is intended as a companion piece to General Hydroponics Pro feedcharts for FloraPro, Flora Series, Cocotek and Maxi Series.

  • Absolutely! All of our nutrient blends contain the necessary elements for plant growth. Start with the formula ratios identified on the label for the specific plant or crop you are growing, and then adjust and experiment until you find the right formula for your specific need.

    For further information, refer to our Drain to Waste feed charts.

  • pH is a measure of the hydronium ion H3O+. It is based on a logarithmic scale from 0 to 14. “Pure” water has a pH of 7.0. If the pH is less than 7, the solution is acid. If the pH is greater than 7 it is alkaline. Because the scale is logarithmic and not linear, a pH of 6 indicates ten times more H protons than a pH of 7, and a pH of 5 indicates 10 times more protons than a pH of 6.

  • Ventilation is often overlooked as a problem. Plants absorb nutrients when the water molecules in the leaves respire (i.e. evaporate). Better ventilation aids a high transpiration rate, which translates into a greater rate of nutrient uptake. Remember that ventilation means changing the air, not just blowing it around the room (circulation).

  • pH is important because it affects availability and absorption of several of the 16 atomic elements needed for plant growth. Maximum absorption of these elements is found at pH readings 5.5 to 6.5. When pH falls below this range many of the macro elements (N, P, K) have less availability, and absorption of the micro nutrients can reach toxic levels.

  • Water containing too much calcium and magnesium (called “total Hardness”) may create serious problems. Contact your municipal water supplier who can provide you with an analysis of your water supply. If you are using well water, many laboratories can provide you with an analysis if you send them a sample. If the dissolved salts in your water supply measure 200 ppm or more, we strongly recommend that you obtain a water analysis to determine calcium content. Excessive calcium is the main factor in determining if your water is hard. If an analysis of your water supply reveals that the Calcium content of your water supply is greater than 70 ppm (mg/liter) you should use Hardwater FloraMicro. Hardwater FloraMicro provides rapidly growing plants with a combination of chelated micro nutrients uniquely formulated for hardwater conditions. Other options are to collect rainwater, install a reverse osmosis filtration system, or use purified water. Do not use mineral or “spring” water, which can unbalance the nutrient solution, or even be toxic to plants.

Our Pro Feedchart Usage Guide explains how to interpret and use General Hydroponics Pro Feedcharts. It is intended as a companion piece to General Hydroponics Pro feedcharts for FloraPro, Flora Series, Cocotek and Maxi Series.

Absolutely! All of our nutrient blends contain the necessary elements for plant growth. Start with the formula ratios identified on the label for the specific plant or crop you are growing, and then adjust and experiment until you find the right formula for your specific need.

For further information, refer to our Drain to Waste feed charts.

pH is a measure of the hydronium ion H3O+. It is based on a logarithmic scale from 0 to 14. “Pure” water has a pH of 7.0. If the pH is less than 7, the solution is acid. If the pH is greater than 7 it is alkaline. Because the scale is logarithmic and not linear, a pH of 6 indicates ten times more H protons than a pH of 7, and a pH of 5 indicates 10 times more protons than a pH of 6.

Ventilation is often overlooked as a problem. Plants absorb nutrients when the water molecules in the leaves respire (i.e. evaporate). Better ventilation aids a high transpiration rate, which translates into a greater rate of nutrient uptake. Remember that ventilation means changing the air, not just blowing it around the room (circulation).

pH is important because it affects availability and absorption of several of the 16 atomic elements needed for plant growth. Maximum absorption of these elements is found at pH readings 5.5 to 6.5. When pH falls below this range many of the macro elements (N, P, K) have less availability, and absorption of the micro nutrients can reach toxic levels.

Water containing too much calcium and magnesium (called “total Hardness”) may create serious problems. Contact your municipal water supplier who can provide you with an analysis of your water supply. If you are using well water, many laboratories can provide you with an analysis if you send them a sample. If the dissolved salts in your water supply measure 200 ppm or more, we strongly recommend that you obtain a water analysis to determine calcium content. Excessive calcium is the main factor in determining if your water is hard. If an analysis of your water supply reveals that the Calcium content of your water supply is greater than 70 ppm (mg/liter) you should use Hardwater FloraMicro. Hardwater FloraMicro provides rapidly growing plants with a combination of chelated micro nutrients uniquely formulated for hardwater conditions. Other options are to collect rainwater, install a reverse osmosis filtration system, or use purified water. Do not use mineral or “spring” water, which can unbalance the nutrient solution, or even be toxic to plants.